All Parts

AquaPruf™ standard load variable speed totally enclosed non-ventilated gearmotor, 1.0 Hp (0.74kW), 208-230/460 volt, 3 phase, 6-60 Hz. The gearmotor is completely stainless steel and are filled with FDA H1 lubricant. The gearmotor turns at 6-58 RPM. Order variable speed controller separately.

Replacement AquaPruf all stainless gear reducer, 20:1 ratio, NEMA 56C Face. Uncrated weight = 23 lbs. (10.4 kg).

Mounting clip for mounting electrical / air routing on conveyor frame. (pack of 10)

NEMA Standard load fixed speed 3 Phase totally enclosed non-ventilated gearmotor, 20:1 Ratio, 87 RPM, 1 Hp, 208-230/460 volt, 3.5-3.2/1.6 FLA, 3 phase, 60 Hz. The gear reducer is aluminum body with FDA sealed surface conversion and filled with FDA H1 l

1/4-20 self drilling DustPruf slot screw with a clamping range 1/8″-1/2″ (3-12mm). (pack of 10)

5MM X 10″ MATTE GREEN 88A

Shoe, return, plastic chain.

Chain Repair Kit, Type VA chain, 36″ (914mm) wide x 12” (305mm) long.

IDLER SPINDLE, 7600 32″

DRIVE SPINDLE, 7600 32″

Idler puck

Return roller shaft.

Weldment, id bsa 1-7/8 trans lh.

Weldment, id bsa 1-7/8 trans rh.

Bearing aSSy, mod, 3 bolt flange.

Guard,Drive, 6.09 C-C

Support block assembly for .375″ (9.7mm) hex shaft

Tension pin assembly for 5″ wide conveyors.

Sleeve,Retaining,Spindle.

Replacement belt for a 4100 Series end drive conveyor, 5″ (127mm) wide belt x 4′ (1219mm) long, with type 02 standard general purpose belt with fused finger splice.

PE,REFLECTOR 4-3/8″ X 1-1/8″

BELT, 3″CTR POLY-V 3RIB

AquaPruf™ horizontal outrigger mounting sanitary support stand for a 24″ (610mm) wide 7400/7600 conveyor, adjustable height from 35″ to 39″ (889mm – 991mm) top of belt with total locking casters and outriggers. This stand consists of stainless welded

AquaPruf™ horizontal mounting sanitary support stand for a 30″ (762mm) wide 7400/7600 conveyor, adjustable height from 39″ to 43″ (991mm – 1092mm) top of belt with fixed footpads. This stand consists of stainless welded tube construction. and requires

AquaPruf™ horizontal mounting sanitary support stand for a 24″ (610mm) wide 7400/7600 conveyor, adjustable height from 35″ to 39″ (889mm – 991mm) top of belt with total locking casters. This stand consists of stainless welded tube construction and req

Diagonal bracing for H style stands over 30in (762mm) tall.

Diagonal bracing for two-legged H style stands up to 30″ (762mm) tall.

AquaPruf™ 7400/7600 diagonal stand brace 20.5″(521mm) mounting hole center distance

FILLER PLATE,CRV IDLER H LH

FILLER PLATE,CRV IDLER H RH

GAP FILLER PLATE

BEARING HOUSING-FLAT CURVE

Variable speed VFD controller, NEMA 4X enclosure, reversing, 460V, 3 phase, 60 Hz input, 460VAC output, 1.2 amp. Wiring to variable speed controller by customer.

Variable speed VFD controller, NEMA 4X enclosure, reversing, 230V, 3 phase, 60 Hz input, 230VAC output, 2.3 amp. Wiring to variable speed controller by customer. Uncrated weight = 5lb (2kg).

Variable speed VFD controller, NEMA 4X enclosure, reversing, 115V, 1 phase, 60 Hz input, 230VAC output, 2.3 amp. Uncrated weight = 6lb (3kg).

Variable speed VFD controller, NEMA 4 enclosure, reversing, 230V, 3 phase, 60 Hz input, 230VAC output, 2.2 amp. Wiring to variable speed controller by customer. Uncrated weight = 4lb (2kg).

Variable speed VFD controller, NEMA 4 enclosure, reversing, 115V, 1 phase, 60 Hz input, 230VAC output, 2.2 amp. Uncrated weight = 3lb (1kg)

Variable speed full featured controller, 115V, 1 phase, 60 Hz input, 230VAC output, 4 amp

Replacement Heavy load motor, 1.5 Hp (1.11kW), 208-230/460 volt, 3 phase, 60 Hz. Order 3 phase starter separately. Uncrated weight = 34 lbs. (15.5 kg). For gearmotor 32M030EH423FN.

3200 & 3200 LPZ Series eDrive™ adaptor kit to replace an older style (2002-2011) standard load gear reducer / gearmotor on a side drive mounting package. Includes shaft and hardware for mounting an eDrive™ gear reducer (not included). Uncrated weight

3200 Belted & LPZ Belted Series standard load eDrive™ bottom mounting package for an end drive conveyor, mounted in the A position, 18:16 pulley ratio. Uncrated weight = 13 lbs. (5.7 kg).

Heavy load E-Drive 90 Degree VFD Variable Speed gearmotor, .5 Hp (.37kw), 230/460 volt, 3 phase, 15-60 Hz, 22 RPM. Order variable speed controller separately. Uncrated weight = 36lb (16kg

3200 Belted Series standard load 90° shaft eDrive™ variable speed VFD gearmotor, .75 Hp (.55kW) de-rated to .50 Hp (.37kW) for full torque throughout speed range, 230/460 volt, 3 phase, 6-60 Hz, 29 RPM, providing a belt speed of 2.6 – 26 ft/min (0.8 –

Replacement Gear reducer, 30:1 ratio, NEMA 140TC Face. Uncrated weight = 14 lbs. (6.4 kg). For gearmotor 32M030EH423FN.

Heavy load E-Drive 90 Degree Fixed Speed gearmotor, 1.5 Hp (1.1kw), 208-230/460 volt, 3 phase, 60 Hz, 58 RPM. Order 3 phase starter separately. Uncrated weight = 48lb (22kg).

90° shaft variable speed indexing eDrive™ gearmotor, .5 Hp (.37kW), 230/460 volt, 3 phase, 6-60 Hz, 86 RPM. Order variable speed controller separately. Uncrated weight = 21 lbs. (9.6 kg).

Replacement Gear reducer, eDrive, 10:1 ratio, NEMA 42CZ Face. Uncrated weight = 3 lbs. (1.3 kg).

Heavy load E-Drive 90 Degree Fixed Speed gearmotor, .5 Hp (.37kw), 208-230/460 volt, 3 phase, 60 Hz, 345 RPM. Order 3 phase starter separately. Uncrated weight = 20lb (9kg)

Replacement Gear reducer, eDrive, 5:1 ratio, NEMA 56C Face. Uncrated weight = 5 lbs. (2.4 kg).

Replacement belt for a 3200 Series Belted end drive conveyor with V-guide belt tracking, standard 3″ pulley drive tail, 20mm nose bar pulley idler tail , 34″ (864mm) wide belt x 5′ (1,524mm) long, with type 08 standard high friction belt with fused finger