All Parts

Linking cable kit, quick disconnect for all Dorner control devices6ft (1.83 M) long with mounting hardware for 2200, 3200 and LPZ conveyors

Control stop kit, push to stop / pull to start maintained push button, plastic Nema 12 enclosure and quick disconnect receptacle. Horizontal or vertical mounting for 2200, 3200 and LPZ conveyors. Order linking cable kit separately

DRIVE ASSEMBLY, SERIES, 2200-5MM

AquaPruf™ manual motor starter, 400/460 volt, 3phase, 0.63 – 0.99 amps. Includes wiring to motor when ordered with motor, wiring to starter by others. Uncrated weight = 3 lbs. (1.4 kg)

AquaPruf™ standard load fixed speed totally enclosed non-ventilated gearmotor, 0.5 Hp (0.37kW), 230/460 volt, 3 phase, 60 Hz. The gear reducer and motor are completely stainless steel and are filled with FDA H1 lubricant. The gearmotor turns at 29 RPM. Order motor starter separately.

AquaPruf™ standard load variable speed totally enclosed non-ventilated gearmotor, 1.0 Hp (0.74kW), 208-230/460 volt, 3 phase, 6-60 Hz. The gearmotor is completely stainless steel and are filled with FDA H1 lubricant. The gearmotor turns at 6-58 RPM. Order variable speed controller separately.

Replacement AquaPruf all stainless gear reducer, 20:1 ratio, NEMA 56C Face. Uncrated weight = 23 lbs. (10.4 kg).

Mounting clip for mounting electrical / air routing on conveyor frame. (pack of 10)

NEMA Standard load fixed speed 3 Phase totally enclosed non-ventilated gearmotor, 20:1 Ratio, 87 RPM, 1 Hp, 208-230/460 volt, 3.5-3.2/1.6 FLA, 3 phase, 60 Hz. The gear reducer is aluminum body with FDA sealed surface conversion and filled with FDA H1 l

1/4-20 self drilling DustPruf slot screw with a clamping range 1/8″-1/2″ (3-12mm). (pack of 10)

5MM X 10″ MATTE GREEN 88A

Shoe, return, plastic chain.

Chain Repair Kit, Type VA chain, 36″ (914mm) wide x 12” (305mm) long.

IDLER SPINDLE, 7600 32″

DRIVE SPINDLE, 7600 32″

Idler puck

Return roller shaft.

Weldment, id bsa 1-7/8 trans lh.

Weldment, id bsa 1-7/8 trans rh.

Bearing aSSy, mod, 3 bolt flange.

Guard,Drive, 6.09 C-C

Support block assembly for .375″ (9.7mm) hex shaft

Tension pin assembly for 5″ wide conveyors.

Sleeve,Retaining,Spindle.

Replacement belt for a 4100 Series end drive conveyor, 5″ (127mm) wide belt x 4′ (1219mm) long, with type 02 standard general purpose belt with fused finger splice.

PE,REFLECTOR 4-3/8″ X 1-1/8″

BELT, 3″CTR POLY-V 3RIB

AquaPruf™ horizontal outrigger mounting sanitary support stand for a 24″ (610mm) wide 7400/7600 conveyor, adjustable height from 35″ to 39″ (889mm – 991mm) top of belt with total locking casters and outriggers. This stand consists of stainless welded

AquaPruf™ horizontal mounting sanitary support stand for a 30″ (762mm) wide 7400/7600 conveyor, adjustable height from 39″ to 43″ (991mm – 1092mm) top of belt with fixed footpads. This stand consists of stainless welded tube construction. and requires

AquaPruf™ horizontal mounting sanitary support stand for a 24″ (610mm) wide 7400/7600 conveyor, adjustable height from 35″ to 39″ (889mm – 991mm) top of belt with total locking casters. This stand consists of stainless welded tube construction and req

Diagonal bracing for H style stands over 30in (762mm) tall.

Diagonal bracing for two-legged H style stands up to 30″ (762mm) tall.

AquaPruf™ 7400/7600 diagonal stand brace 20.5″(521mm) mounting hole center distance

FILLER PLATE,CRV IDLER H LH

FILLER PLATE,CRV IDLER H RH

GAP FILLER PLATE

BEARING HOUSING-FLAT CURVE

Variable speed VFD controller, NEMA 4X enclosure, reversing, 460V, 3 phase, 60 Hz input, 460VAC output, 1.2 amp. Wiring to variable speed controller by customer.

Variable speed VFD controller, NEMA 4X enclosure, reversing, 230V, 3 phase, 60 Hz input, 230VAC output, 2.3 amp. Wiring to variable speed controller by customer. Uncrated weight = 5lb (2kg).

Variable speed VFD controller, NEMA 4X enclosure, reversing, 115V, 1 phase, 60 Hz input, 230VAC output, 2.3 amp. Uncrated weight = 6lb (3kg).

Variable speed VFD controller, NEMA 4 enclosure, reversing, 230V, 3 phase, 60 Hz input, 230VAC output, 2.2 amp. Wiring to variable speed controller by customer. Uncrated weight = 4lb (2kg).

Variable speed VFD controller, NEMA 4 enclosure, reversing, 115V, 1 phase, 60 Hz input, 230VAC output, 2.2 amp. Uncrated weight = 3lb (1kg)

Variable speed full featured controller, 115V, 1 phase, 60 Hz input, 230VAC output, 4 amp

Replacement Heavy load motor, 1.5 Hp (1.11kW), 208-230/460 volt, 3 phase, 60 Hz. Order 3 phase starter separately. Uncrated weight = 34 lbs. (15.5 kg). For gearmotor 32M030EH423FN.

3200 & 3200 LPZ Series eDrive™ adaptor kit to replace an older style (2002-2011) standard load gear reducer / gearmotor on a side drive mounting package. Includes shaft and hardware for mounting an eDrive™ gear reducer (not included). Uncrated weight

3200 Belted & LPZ Belted Series standard load eDrive™ bottom mounting package for an end drive conveyor, mounted in the A position, 18:16 pulley ratio. Uncrated weight = 13 lbs. (5.7 kg).

Heavy load E-Drive 90 Degree VFD Variable Speed gearmotor, .5 Hp (.37kw), 230/460 volt, 3 phase, 15-60 Hz, 22 RPM. Order variable speed controller separately. Uncrated weight = 36lb (16kg

3200 Belted Series standard load 90° shaft eDrive™ variable speed VFD gearmotor, .75 Hp (.55kW) de-rated to .50 Hp (.37kW) for full torque throughout speed range, 230/460 volt, 3 phase, 6-60 Hz, 29 RPM, providing a belt speed of 2.6 – 26 ft/min (0.8 –

Replacement Gear reducer, 30:1 ratio, NEMA 140TC Face. Uncrated weight = 14 lbs. (6.4 kg). For gearmotor 32M030EH423FN.

Heavy load E-Drive 90 Degree Fixed Speed gearmotor, 1.5 Hp (1.1kw), 208-230/460 volt, 3 phase, 60 Hz, 58 RPM. Order 3 phase starter separately. Uncrated weight = 48lb (22kg).